Could you please disclose informations about the SuperFlex's

• 
  Cure Depth [mm] 
  


• 
  Depth of penetration (as the working curve)
  


• 
  Critical Energy [J/mm2] 
  

Thank you

Could you please disclose informations about the SuperFlex's

• Cure Depth [mm] 


• Depth of penetration (as the working curve)


• Critical Energy [J/mm2] 

Thank you

Dear Customer,

Thank you for your inquiry regarding the curing parameters for SuperFlex.

We can provide the exposure settings, such as exposure time, for SuperFlex based on the 3D printers that we have tested.

However, we do not currently have separate measurement data for the curing-depth-related parameters you requested, such as Cure Depth, Depth of Penetration (Dp), and Critical Energy (Ec), so unfortunately we are unable to provide these values at this time.

Could you please let us know the3D printer model you are currently using? We will check whether we have the recommended exposure settings for your printer and provide them to you if available.

Good morning, can you please tell us the parameters to print the Superflex Clear resin using the Anycubic Photon P?

Kind regards 

Matteo Bentivogli

Good morning, can you please tell us the parameters to print the Superflex Clear resin using the Anycubic Photon P?

Kind regards 

Matteo Bentivogli

Dear Mr. Bentivogli,

Thank you for your inquiry.

For printing SuperFlex Clear with the Double Platform on the Anycubic Photon P1, we recommend the following initial settings:

Printer: Anycubic Photon P1

Platform: Double Platform

Layer Height: 50 µm

Bottom Exposure: 20.0 s

Bottom Layers: 4

Normal Exposure: 1.7 s

Light-off Time: 2.5 s

Lift Distance: 6 mm

Lift Speed: 2 mm/s

Retract Speed: 2 mm/s

Resin Temperature: 25–30°C

When using the Double Platform, the cured area per layer and the peel force may be greater than with a single platform. Therefore, we recommend using a lower lift speed and allowing sufficient light-off time.

Please try printing with the above settings first. Depending on the print results, we recommend adjusting the Normal Exposure Time by ±0.1–0.2 sec as needed.

We hope these settings help, and please let us know the results.

Kind regards,

3DMaterials Co., Ltd.

Cuales son los Parametros de impresion uniformation GK3 para la resina super Flex ENR-F12L?

Gracias,

Cuales son los Parametros de impresion uniformation GK3 para la resina super Flex ENR-F12L?

Gracias,

Dear Customer,

Thank you for your inquiry.

For SuperFlex ENR-F12L resin with the Uniformation GK3, we recommend the following initial settings at a 50 µm layer height:

-. Layer Height: 50 µm

-. Bottom Exposure: 12–15 s

-. Bottom Layers: 5 layers

-. Normal Exposure: 1.7–2.0 s

As a starting point, we recommend testing with a Normal Exposure of 1.8 s.

Please note that these are estimated initial settings, and some adjustments may be required depending on the printer condition and the geometry of the printed part.

Thank you.

Hello,

your website says that the mentioned material has been certified to ISO 10993 if correctly post-processed. Neither on the website nor in the datasheets there is any information about curing with UV light or heat or any other clue how to do so, apart fr|om the rinsing information. Please provide these information to everyone as otherwise your claim remains void. If your material shall comply, you have generated a very unique and interesting product with a large group of prospect buyers.

Thanking you in anticipation,

Best regards

Hello,

your website says that the mentioned material has been certified to ISO 10993 if correctly post-processed. Neither on the website nor in the datasheets there is any information about curing with UV light or heat or any other clue how to do so, apart fr|om the rinsing information. Please provide these information to everyone as otherwise your claim remains void. If your material shall comply, you have generated a very unique and interesting product with a large group of prospect buyers.

Thanking you in anticipation,

Best regards

Dear Customer,

Thank you for your feedback and for raising this important point.

Properly cleaned and fully post-cured SuperFlex, SuperElastic, and other applicable printed parts pass ISO 10993-5 testing. The sample preparation and post-processing procedure used for the ISO 10993-5 evaluation is described in our User Guide (page 69).

User Guide Download

The recommended procedure is as follows:

1. Clean the printed part with IPA (isopropyl alcohol), followed by a quick rinse in acetone to remove any residual tackiness.


2. For more thorough cleaning, use an IPA bath with ultrasonic agitation for approximately 10 minutes to ensure complete removal of uncured resin.


3. Remove all support structures and smooth any remaining surface imperfections using sandpaper or appropriate grinding tools.


4. Wash away any residue using water or IPA and dry the part completely using compressed air or air drying, ensuring no solvent remains on the surface.


5. Post-cure the printed part in a UV post-curing unit for 20–30 minutes, adjusting the duration according to the equipment manufacturer's recommendations.


6. As an optional final step, immerse the post-cured part in water or glycerin for approximately 10 minutes to eliminate any residual surface tackiness and achieve a fully cured surface.

We appreciate your suggestion regarding the visibility of this information and will review whether additional references can be added to our website and datasheets to make these requirements easier to locate.

Thank you again for your interest in our materials and for your valuable feedback. Please let us know if you have any further questions.

This is for the superfast superflex clear resin. 

This resin came out of the bottle very thin, and slightly cloudy and chunky and did not print at all on a Elegoo Saturn 4 Ultra. Is this the expected appearance of the resin? Can you recommend any troubleshooting for getting this to work? I used 10sec exposure for initial layers and 1.4 for normal layers.

This resin came out of the bottle very thin, and slightly cloudy and chunky and did not print at all on a Elegoo Saturn 4 Ultra. Is this the expected appearance of the resin? Can you recommend any troubleshooting for getting this to work? I used 10sec exposure for initial layers and 1.4 for normal layers.

Dear Customer

We’re very sorry to hear about the issue you experienced and apologize for the inconvenience.

To better assist you, could you please let us know which resin you were using? 

For example, SuperHDT could be crystallize due to lower temperatures storage. In such cases, we recommend gently warming the bottle at 60°C for an hour  or 50°C for couple of hours.

Once we know exactly which resin you used, we will be able to provide more specific troubleshooting guidance 

Thank you for your cooperation, and we look forward to your reply.

Hi, 

can you give me a more detailed description of the washing process for the Super Flex? Is this material washable in water or only in IPA? On the amazon page it says water washable. Mostly i use water washable resins. Can it be combined with Super Flex? Which ratio is best for combining? How long do the printed parts to be cured? I use an Elegoo Saturn 4 Ultra 16K and the Elegoo Mercury Plus v3.0. Thanks for your answer.

Kind regards

Michael Breunig

Hi, 

can you give me a more detailed description of the washing process for the Super Flex? Is this material washable in water or only in IPA? On the amazon page it says water washable. Mostly i use water washable resins. Can it be combined with Super Flex? Which ratio is best for combining? How long do the printed parts to be cured? I use an Elegoo Saturn 4 Ultra 16K and the Elegoo Mercury Plus v3.0. Thanks for your answer.

Kind regards

Michael Breunig

Thank you for using SuperFlex. 

We recommend to wash a printing with any type of alcohol, includingIPA(isopropylalcohol)and ethanol if you use Engineering resin as like SuperFlex. 

even if we recommend to use warm tap water and soap for the printing with SuperFast 4k and 8K. 

in case of using SuperFlex, a printing might be sticky after clean. 

The best way to remove the surface stickiness is the underwater (under glycerin) post-curing 10mins.

1.After print, remove the excess resin by compressed air

2.If you want, quick cleaning with IPA less than 5 mins, or acetone rinse 

3.Then 5 mins quick curing, then another 5 min curing underwater (under glycerin)

The sticky surface is not induced by excess resin, the oxygen in air cause curing inhibition during post-curing.

The best results we saw were only by compressed air cleaning + 5 mins post-curing in air + 5 mins post-curing under water.

if you have a question, please feel free to contact us. 

can you tell me the specific settings for the super flex clear resin on the Photon Mono 4 Ultra?

Thanks!

can you tell me the specific settings for the super flex clear resin on the Photon Mono 4 Ultra?

Thanks!

Dear Sir 

thank you for using SuperFlex. 

we recommend below setting for AnyCubic Photon Mono 4 Ultra.

-. Slicing : 50um 

-. Bottom Layers : 10.0s

-. Normal Layers : 1.5~1.8s 

The above conditions are expected output conditions and may require fine adjustment depending on the output environment and model shape.

¿Sería tan amable de proporcionarme los parámetros de impresión a 50 μm para la Anycubic Photon Mono M7 Max?

¿Sería tan amable de proporcionarme los parámetros de impresión a 50 μm para la Anycubic Photon Mono M7 Max?

Dear Sir 

First of all, we apologize for the delayed response.

Since the printing parameters vary depending on the specific resin, could you please let us know which product you are using? Once we have that information, we will be happy to check and provide the appropriate settings for you.

For your reference, you can also find resin-specific printing parameters at the link below:

User Guide Download

Please feel free to contact us if you need any further assistance.

¿Sería tan amable de proporcionarme los parámetros de impresión a 50 μm para la Anycubic Photon Mono M7 Max?

¿Sería tan amable de proporcionarme los parámetros de impresión a 50 μm para la Anycubic Photon Mono M7 Max?

Dear Sir 

First of all, we apologize for the delayed response.

Since the printing parameters vary depending on the specific resin, could you please let us know which product you are using? Once we have that information, we will be happy to check and provide the appropriate settings for you.

For your reference, you can also find resin-specific printing parameters at the link below:

User Guide Download

Please feel free to contact us if you need any further assistance.

Dear Sir

First of all, we apologize for the delayed response.

The recommended shelf life of SuperFlex Clear Resin is 5 years fr|om the date of manufacture, provided it is stored under proper conditions.

The expiration date is printed at the bottom of the label on the bottle.

For your reference, products manufactured more recently will show an expiration period of 5 years fr|om the manufacturing date.

However, some earlier batches may display a 2-year shelf life on the label.

We revised and standardized our shelf-life policy this year, extending it fr|om 2 years to 5 years based on updated internal validation.

Please feel free to let us know if you have any further questions.

can you provide a profile for printing with  asiga max uv 385?

thanks

can you provide a profile for printing with  asiga max uv 385?

thanks

Thank you for your inquiry.

Unfortunately, we do not have an Asiga printer on hand, so we’re unable to provide a specific printing profile for the Asiga Max UV 385 at this time.

please understand it. 

Please feel free to let us know if you need any other assistance.

What is the density of the material in its liquid form and after curing?

What is the density of the material in its liquid form and after curing?

Thank you for your asking. 

Regarding your inquiry, please see the information below:

The density of general liquid resins such as the STANDARD SERIES and ENGINEERING SERIES is approximately 1.05 to 1.15 g/cm³.

However, as an exception, the SuperRigid has a relatively higher density of approximately 1.32 g/cm³.

After curing, the density typically increases by about 5% to 10%.

Thank you. 

Hello, can you please specify the settings for the Elgoo Mars 5 Ultra with superflex clear? Thanks. 

Hello, can you please specify the settings for the Elgoo Mars 5 Ultra with superflex clear? Thanks. 

Thank you for using SuperFlex. 

we recommend below setting for Elegoo Mars 5 Ultra.

-. Slicing : 50um 

-. Bottom Layers : 10.0s

-. Normal Layers : 1.5s

if you have any question, please feel free to contact us. 

Thank you for using SueprFlex. 

We recommend below setting for Anycubic Photon Mono M5s Pro.

-. Slicing : 50um 

-. Bottom layers : 10.0s

-. Normal layers : 1.7s

if you have another question, please feel free to contact us. 

Dear Sir/Madam,

 Is this material biocompatible? Can it be considered a medical-grade resin, if not, would you have products with similar mechanics and applicable to medical applications and medical implant design?

Thank you for your time,

Best wishes,

Ahmed