|
No. |
Title |
Writer |
Date |
|
42 |
Photon S |
alexandruciorba |
2024.04.16 |
|
Hi, I'd like to print your Superflex resin with a Photon S.
How should I set up times, please?
Thank you :)
|
|
41 |
Photon S |
3DMaterials |
2024.04.16 |
|
Hi, I'd like to print your Superflex resin with a Photon S.
How should I set up times, please?
Thank you :)
==================== 답 변 ====================
Thank you for using SuperFlex.
we recommend below setting for Anycubic
Photon S.
Slicing 50um
Bottom Layer : 20.0s
Normal Layer : 7.0s
thank you and have a good day.
|
|
40 |
Setting parameters for Elegoo Saturn S |
ricky |
2024.04.11 |
|
Hi Guys,
I recently purchased the superflex resin, could you kindly provide me with the parameters for the Elegoo Saturn S
Thank you
Ricky
|
|
39 |
Setting parameters for Elegoo Saturn S |
3DMaterials |
2024.04.12 |
|
Hi Guys,
I recently purchased the superflex resin, could you kindly provide me with the parameters for the Elegoo Saturn S
Thank you
Ricky
==================== 답 변 ====================
Thank you for using SuperFlex.
We recommend below setting for Elegoo Saturn S.
Slicing : 50um
Bottom Layers : 10.0s
Normal Layers : 1.8s
|
|
38 |
Print setting for Phrozen Sonic Mega 8K |
YL |
2024.02.07 |
|
Hi, do you have the print setting for SuperFlex for Phrozen Sonic Mega 8K printer, and clean & post-curing procedures using Phrozen wash and cure kit?
|
|
37 |
Print setting for Phrozen Sonic Mega 8K |
3DMaterials |
2024.02.09 |
|
Hi, do you have the print setting for SuperFlex for Phrozen Sonic Mega 8K printer, and clean & post-curing procedures using Phrozen wash and cure kit?
==================== 답 변 ====================
Thank you for using SuperFlex. Please use below setting for Sonic Mega 8K
Slicing: 50um
Bottom Layer: 15.0 secs
Printing Layer: 2.5 secs
|
|
36 |
Elegoo Mars 4 Optimal Settings |
Elliot |
2023.11.03 |
|
Hello, unfortunately I was unable to find the light intensity specifications for the Mars 4. Can you please provide the optimal settings for that printer? Thank you.
|
|
35 |
Print settings for Phrozen Mighty 8K |
Justin Poulsen |
2023.10.26 |
|
Hi, do you have suggested print settings for the Phrozen Mighty 8k using the SuperFast SuperElastic ENGR-E38L Resin?
Thank you,
Justin
|
|
34 |
Print settings for Phrozen Mighty 8K |
3DMaterials |
2023.10.27 |
|
Hi, do you have suggested print settings for the Phrozen Mighty 8k using the SuperFast SuperElastic ENGR-E38L Resin?
Thank you,
Justin
==================== 답 변 ====================
Hello
Thank you so much for using SuperElastic.
Please use below exposure settings for Mighty 8K with SuperElastic
Slicing : 50um
Bottom Layers : 20. 0 secs
Normal Layers : 1.9 secs
Thank you
|
|
33 |
Curing procedure? |
Eddie |
2023.10.19 |
|
Hi, i'm printing Superflex with the exact specified parameters on an Elegoo Saturn. Initially, the prints turned out well but after curing the were sticky as glue!
I read on a forum that for curing, the prints should be covered with water to seal them fr|om oxygen which would cause the stickyness while curing.
I print small pieces the size of a pen cap for medical purposes. If i put them in a beaker, cover them with water and cure them for 1h (!) they are no longer
sticky but the surface is no longer smooth but very rough. I found that letting the prints dry on Kleenex over night instead of drying them with hot air
does less harm to the surface but they are still not smooth.
Is there any recommended curing procedure i can follow to get flexible, clear and smooth prints that aren't sticky?
Thanks, E.
|
|
32 |
Curing procedure? |
3DMaterials |
2023.10.19 |
|
Hi, i'm printing Superflex with the exact specified parameters on an Elegoo Saturn. Initially, the prints turned out well but after curing the were sticky as glue!
I read on a forum that for curing, the prints should be covered with water to seal them fr|om oxygen which would cause the stickyness while curing.
I print small pieces the size of a pen cap for medical purposes. If i put them in a beaker, cover them with water and cure them for 1h (!) they are no longer
sticky but the surface is no longer smooth but very rough. I found that letting the prints dry on Kleenex over night instead of drying them with hot air
does less harm to the surface but they are still not smooth.
Is there any recommended curing procedure i can follow to get flexible, clear and smooth prints that aren't sticky?
Thanks, E.
==================== 답 변 ====================
Hello, thank you so much for using SuperFlex.
There are many tips to solve the curing issue, below steps are what we do in our lab.
Some of sequence can be changed or deleted depending on the design of printer and curing device.
1.After printing, we use compressed air to remove excess resin in the print (not washing).
2.Cure the print with support.
3.Remove all support by cutter and grind off all bump and even out the over cure area using sandpaper or grinding tools.
4.Washing off the residue fr|om griding using water or IPA
5.Recoat the print by dipping in the same resin, or by flow coating with the resin.
6.Leave the recoated print until excess resin flow off, and post-cure the print in air first.
7.Then, post-cure it again under water or glycerin.
|
|
31 |
Stability SuperFlex |
Gregor |
2023.08.22 |
|
Hello,
the material has no tensile strength after curing.
A 1mm thick wall is even easier to tear than cardboard.
Is this normal?
Regards Jan
|
|
30 |
Stability SuperFlex |
3DMaterials |
2023.08.24 |
|
Hello,
the material has no tensile strength after curing.
A 1mm thick wall is even easier to tear than cardboard.
Is this normal?
Regards Jan
==================== 답 변 ==================== Thank you for using SuperFlex. 1mm thickness is quite thin and if you need more strength,
|
|
29 |
Anycubic Photon Recommended Settings |
Edmund Totah |
2023.07.21 |
|
Hello,
What settings do you recommend for the Original Anycubic Photon? I would ideally like to print at 25um.
Thanks!
|
|
28 |
Anycubic Photon Recommended Settings |
3DMaterials |
2023.07.21 |
|
Hello,
What settings do you recommend for the Original Anycubic Photon? I would ideally like to print at 25um.
Thanks!
==================== 답 변 ====================
Thank you so much for using SuperFlex
Please use following settings for 25um with Photon S (Normal LCD)
Bottom Layer : 30.0 secPrinting Layer : 6.5 sec
|
|
27 |
Photon M3 Max Settings |
muffinman |
2023.07.16 |
|
What settings should I use for the Anycubic Photon M3 Max?
|
|
26 |
Photon M3 Max Settings |
3DMaterials |
2023.07.18 |
|
What settings should I use for the Anycubic Photon M3 Max?
==================== 답 변 ====================
SuperFlex For 50um slicing, we recommend Bottom Layer : 10.0 ~ 15.0 secs Printing Layer : 2.2 ~ 2.5 secs
|
|
25 |
Settings for EPAX X10 5K |
Patrick Bock |
2023.06.16 |
|
Hi. Does anyone know the best settings for this printer?
|
|
24 |
Settings for EPAX X10 5K |
3DMaterials |
2023.06.16 |
|
Hi. Does anyone know the best settings for this printer?
==================== 답 변 ==================== Hello, thank you so much for using SuperFlex. I don't have actual tested setting for EPAX X10 5K, but the estimated settings are Slicing 50um Bottom Layer 5.0 ~ 8.0 secsPrinting Layer 1.5 ~ 1.8 secsThank you |
|
23 |
[SuperFlex] Clear Settings on Prusa SL1S |
BM |
2023.03.30 |
|
Could you specify the recommended print settings for [SuperFlex] Clear on Prusa SL1S?
|
|
22 |
[SuperFlex] Clear Settings on Prusa SL1S |
3DMaterials |
2023.03.31 |
|
Could you specify the recommended print settings for [SuperFlex] Clear on Prusa SL1S?
========================================
Thank you so much for using SuperFlex.
For 50um slicing, we recommend
Bottom Layer 20 sec
Printing Layer 2.5 sec
Thank you
3DMaterials
|
|
21 |
Elegoo Saturn 2 settings, post-cure in Mercury XS |
E. Cold |
2023.03.02 |
|
Recently purchased SuperFlex resin! I'd like to know the exposure settings for Elegoo Saturn 2 8k since they're not present in the resin sheet and what is the curing time inside Mercury XS Cure station (can't find station's cure power in mW/cm2 or J/cm2). Many thanks in advance!
|
|
20 |
Elegoo Saturn 2 settings, post-cure in Mercury XS |
3DMaterials |
2023.03.02 |
|
Recently purchased SuperFlex resin! I'd like to know the exposure settings for Elegoo Saturn 2 8k since they're not present in the resin sheet and what is the curing time inside Mercury XS Cure station (can't find station's cure power in mW/cm2 or J/cm2). Many thanks in advance!
==================== 답 변 ==================== Hello, Thank you so much for using SuperFlex.We recommend the same setting of Mars 2 / Mars 2 Pro for Saturn 2 8K.<50um Slicing>Bottom 5.0 SecsPrinting Layer 1.3 Secs ~ 1.4 Secs |
|
19 |
Elegoo Saturn 2 settings, post-cure in Mercury XS |
3DMaterials |
2023.03.02 |
|
Recently purchased SuperFlex resin! I'd like to know the exposure settings for Elegoo Saturn 2 8k since they're not present in the resin sheet and what is the curing time inside Mercury XS Cure station (can't find station's cure power in mW/cm2 or J/cm2). Many thanks in advance!
==================== 답 변 ==================== Hello, Thank you so much for using SuperFlex.We recommend the same setting of Mars 2 / Mars 2 Pro for Saturn 2 8K.<50um Slicing>Bottom 5.0 SecsPrinting Layer 1.3 Secs ~ 1.4 Secs
==================== 답 변 ==================== Unfortunately, we don't have data for Mercury XS Cure station, we recommend 10 minutes with 20mW/cm2 LED power |
|
18 |
Bulk purchasing |
William |
2023.01.02 |
|
I'm looking for a company that is willing to sell 3-D printable resin in 5 gallon containers. I've looked at more common places to purchase such as Amazon and others etc. etc. and now I'm waiting back fr|om one other place to send me a catalog. Does your company sell raisins in bulk please get back to me send me an email thank you.
|
|
17 |
Bulk purchasing |
3DMaterials |
2023.01.02 |
|
I'm looking for a company that is willing to sell 3-D printable resin in 5 gallon containers. I've looked at more common places to purchase such as Amazon and others etc. etc. and now I'm waiting back fr|om one other place to send me a catalog. Does your company sell raisins in bulk please get back to me send me an email thank you.
==================== 답 변 ==================== Hello, thank you for the inquiry. Yes, we do supply in bulk format. I will contact you shortly via email. Thank you |
|
16 |
Anycubic Photon D2 (DLP) |
Michael |
2022.11.16 |
|
What would you suggest for Exposure time (Bottom/Normal) for your SuperFast/SuperFlex resin when using Anycubic Photon D2.
|
|
15 |
Anycubic Photon D2 (DLP) |
3DMaterials |
2022.11.17 |
|
What would you suggest for Exposure time (Bottom/Normal) for your SuperFast/SuperFlex resin when using Anycubic Photon D2.
==================== 답 변 ==================== Hello SuperFast is for LCD 3D printer, we have not test Photon D2 which use DLP as image source. We recommend use SuperFast with LCD 3D printer. Thank you |
|
14 |
Parameters for Elegoo Mars 3 |
Elmar |
2022.08.16 |
|
Can you please give me the parameters for Elegoo Mars 3 printer?
Thank you Elmar
|
|
13 |
Parameters for Elegoo Mars 3 |
3DMaterials |
2022.08.16 |
|
Can you please give me the parameters for Elegoo Mars 3 printer?
Thank you Elmar
==================== 답 변 ====================
Mars 3 has the same light intensity as Mars 2.
R&D recommended the same setting as Mars 2
50um Slicing, Bottom layer 10 Secs and Print Layer 1.3 Secs.
|
|